Posts mit dem Label level control / Füllstandsregelung werden angezeigt. Alle Posts anzeigen
Posts mit dem Label level control / Füllstandsregelung werden angezeigt. Alle Posts anzeigen

20. Juli 2014

A new filter and a new pyrotouch

Hi All,

New Filter design, First part of the video.

I just posted a video of a test of my new filter setup. The previous filter a combination of cokes coal/woo/stainless steel shavings works well but created Too much presure drop. Also It was a real mess this coals SS shavings ... ugly smell and difficult to clean or to dispose.
This filtersetup is far more lighter in aplication and has very little pressure drop. Off coarse I have tested it only for 2.5 hours so I can not tell how fast it will pack up with dirt.

New pyrotouch/kompaktor/agitator. Second part of the video.

A DriZzLeR beeing a gasifier working in drip feed need to be feed the least possible amount of fuel. Also the flaming pyrolyse zone should be kept very shallow and always at the same level. This is easy if you have a constant load; then just DriZzle in on time interval. But coupled on a generator in island mode with various laod demands and thus various fuel consumption, on should have some kind of a level sensing device to feed more under heavy load and less in idle load. The Pyrotouch/kompaktor works fine with dense fuel such as pellets. With Woodchips the constant hitting the fuel, even if only very little force, is kompakting the reduction  too much and after some hours the reduction is packed densely and the gasifier stops breathing.
Also when DriZzling in pellets the distribute fine all over the flaming pyrolyse. Woodchips are falling down in one chute and pile up on one side of the fuel tube. The other side gets no wood and burns empty with as result a big hollow burn. So the Pyrotouch should have one more function exstra, an agitator and leveling function to make an even and level flaming zone. In the second part of the video I show an attempt to achieve this goal. Unfortunatly the mikroswitch beeing too close to the hot zone melted. Adaptations are needed But the principe seems to work.

Have a look in this video, subscribe, advise and comment




Luk

16. Mai 2014

Automatic DriZzleR on woodchips

Hello fellow DriZzleRs,

I just uploaded a video with a demonstration of another automatic DriZzleR. The first was (Pascal's unit on pellets, this one works solomly on woodchips). The video show a still very rudimental laboratory set up, but one can clearly see in what direction we are going. The ultimate goal is a fully automatic cogeneration- unit on woodchips for heating and energy.



Thank you for watching.

Luk

22. Februar 2014

feeding the DriZzleR automatically and load balanced / Automatische und Lastabhängige Brennstoff Zuführung

Today I have built the "Pyrotouch".

The "Pyrotouch" touches lightly the surface of the flaming pyrolysis at a pressure of about 100g. The light touch is important for the function of the DriZzleR. If the pressure is too strong, too much is promoted and the Flaming Pyrolysis "Drowns". Therefore, here again less is more. Somehow, as with almost all parts of the DriZzleR :-).
 
This Light pressure checks whether the level of flaming pyrolysis has dropped, feeding only as much after as is needed. Thus, it remains always in the same place. Even when the load changes, it regulates steadily more or less fuel. Also different or mixed fuel can now be automatically Gassed.


As soon as "pressed" on the switch, one second operates the auger. When the switch is pressed a second time the game starts all over again.

The rotation of the motor is about one second.

All happens so often, until the shaft through the fuel supplied can not move down far enough to actuate the switch.

Then the level of the flaming pyrolysis is reached.

Now now also an automatic cleaning of the grate is possible. By the rotation of the grate, the fuel decreases. The "Pyrotouch" automatically adjusts back to the correct level.
 


Now it is possible to feed the DriZzleR Gasifier also load depending and automatically.





Heute habe ich den "Pyrotouch" gebaut.


Der "Pyrotouch" berührt nur leicht die Oberfläche der Flammenden Pyrolyse mit einem Druck von ca 100g. Das leichte berühren ist wichtig für die Funktion des DriZzleRs. Wenn der Druck zu stark ist, wird zuviel gefördert und die Flammende Pyrolyse "Ertrinkt". Daher ist auch hier mal wieder weniger ist mehr. Irgendwie wie bei fast allen Teilen am DriZzler :-).

Dieser Leichte Druck prüft ob das Level der Flammenden Pyrolyse abgefallen ist und füttert nur soviel nach wie auch benötigt wird. Damit bleibt sie immer an der gleichen Stelle. Auch bei Lastveränderungen regelt sie stetig mehr oder weniger Brennstoff. Auch unterschiedlicher oder gemischter Brennstoff können nun automatisch Vergast werden.

Sobald auf den Schalter "gedrückt" wird, wird eine Sekunde die Förderschnecke betätigt. Wenn der Schalter ein zweites Mal gedrückt wird beginnt das Spiel wieder von vorne.

Der Umlauf des Motor beträgt etwas über eine Sekunde.

Das ganze passiert so oft, bis sich die Welle durch den zugeführten Brennstoff nicht mehr weit genug nach unten bewegen kann um den Schalter zu betätigen.

Dann ist das Level der flammende Pyrolyse erreicht.

Jetzt ist nun auch ein automatischen Abreinigen des Rostes möglich. Durch das drehen des Rostes, sinkt der Brennstoff ab. Der "Pyrotouch" regelt automatisch wieder auf das richtige Level.

Nun ist es möglich den DriZzleR Vergaser auch Automatisch und Lastabhängig zu befüllen.

15. Februar 2014

Füllstandsüberwachung mit dem "Pyrotouch"


Beim DriZzleR gibt es ein kleines Problem. Der Füllstand muss immer konstant gehalten werden. Damit die Flammende Pyrolyse immer auf der gleichen Höhe bleibt und nur soviel Brennstoff eingefüllt wird wie auch benötigt wird. Das kann man manuell machen und daneben stehen, aber es geht auch komfortabler. Bei einem Motor der immer mit der gleichen Belastung läuft kann man für 6-7 Stunden Dauerbetrieb bei gleich bleibenden Brennstoff zeitgesteuert eine Förderschnecke antreiben. Das funktioniert wunderbar bei Pellets. Bei Hackschnitzeln kann es zu Problemem kommen, da diese kein genormter Brennstoff ist und auch die Qualität sowie die Oberfläche stark unterscheidet. Dafür gibt es unterschiedliche Systeme die getestet werden müssen. Ein gutes System ist vom User Holzgasjournal gebaut worden. Welches in der nächsten Zeit für den DriZzle Betrieb getestet und nachgebaut wird. In unserem Fall nennen wir diese Finger "Pyrotouch".

vielen Dank Holzgasjournal für diese super einfache Füllstandsregelung!


http://youtu.be/n57A_GcHLjk

Level control with the "Pyrotouch"


 The DriZzleR has only one difficult thing. The filling level must be kept constant.
Thus, the Flaming Pyrolysis always remains at the same level and only as much fuel is filled in as is needed. This can be done manually and stand next to it, but it's also comfortable. For a motor that is always running with the same load can be up to 6-7 hours of continuous operation at constant fuel timed drive a auger. This works wonderfully for pellets. With wood chips may cause in some problems, as this is not a standardized fuel and also the quality and the surface is very different. There are different systems that need to be tested. A good system has been built from holzgasjournal. What is tested and rebuilt in the near future for the DriZzleR .We will call it the "Pyrotouch".


many thanks to Holzgasjournal for this easy level control!